Skip to main content

Aparna RMC

curing of concrete

Curing of concrete means keeping freshly placed concrete moist and at a suitable temperature so that cement hydration can continue. Proper curing helps concrete develop the required strength and durability. Even a well-designed concrete mix can lose strength if it dries too early.

This guide explains the curing period of concrete, different curing methods, how long concrete should be cured, and how curing is done for slabs, columns, and other concrete elements.

Key Takeaways

  • Curing keeps concrete moist so cement hydration can continue. It helps concrete develop strength and durability.
  • Under IS 456, the minimum curing period is generally 7 days for ordinary Portland cement and 10 days or more for concrete containing blended cements or mineral admixtures.
  • Water curing, including ponding, sprinkling, and fogging, is a common method where enough water is available.
  • Curing compounds can be used for large areas or sites where regular water curing is difficult.
  • Hot and cold weather can affect the curing period and require suitable site practices.

What Is Curing of Concrete?

Curing of concrete means keeping the concrete moist and at a suitable temperature for a required period after placing. This gives cement enough water to continue hydration. During hydration, cement reacts with water and forms products such as calcium-silicate-hydrate (C-S-H), which help the concrete gain strength. If concrete loses moisture too quickly, hydration slows down, and the surface can become weak and prone to cracking.

How curing affects concrete strength

Concrete continues to gain strength while cement particles have enough water for hydration. If curing is stopped too early, the concrete may not reach its required strength. Poor curing can also affect the surface, leading to dusting, cracking, and lower resistance to wear.

Curing vs setting vs drying

These three terms refer to different stages or processes:

  • Setting is the stage when fresh concrete starts becoming stiff and loses its plasticity.
  • Curing is the process of keeping concrete moist and at a suitable temperature so that hydration and strength development can continue.
  • Drying happens when moisture leaves the concrete. If concrete dries too quickly during the early stages, it can affect strength and increase the risk of cracking.

Why Curing of Concrete Is Important?

Proper curing helps concrete develop the strength and durability expected from the mix. It also helps reduce moisture-related problems on the surface.

  • Higher compressive and flexural strength
  • Lower permeability
  • Better resistance to abrasion and wear
  • Lower risk of shrinkage cracking
  • Better durability against weathering and chemical exposure
  • A denser and more uniform surface

What happens if concrete is not cured properly

Poorly cured concrete can have:

  • Lower final strength
  • Surface dusting and scaling
  • More shrinkage cracks
  • Higher permeability
  • Greater risk of water and chloride penetration
  • Reduced service life

When Should Curing of Concrete Start?

Curing should begin as soon as the concrete surface is firm enough to receive the selected curing method without being damaged. Initial protection against rapid moisture loss should begin as soon as the surface is finished, particularly in hot, dry or windy conditions. Water curing can begin once water application will not damage or mark the surface.

On site, the surface should be checked before water is applied. A practical check is to press the surface lightly with a thumb. If the surface is firm enough not to be marked or damaged, water curing can be started.

Curing Period of Concrete: How Many Days?

Under IS 456:2000, concrete surfaces should generally be kept moist or wet for at least 7 days when ordinary Portland cement is used and at least 10 days when blended cements or mineral admixtures are used. In dry and hot weather, curing should continue for at least 10 days, while 14 days is recommended when blended cements or mineral admixtures are used.

The 28-day period is commonly used to assess the specified compressive strength of concrete. It does not mean that concrete must be continuously water-cured for exactly 28 days. The required curing period depends on the cement type, concrete mix, weather conditions and project requirements.

Curing period by cement type and weather condition

Cement type / conditionModerate temperature & humidityHot & dry weatherCold weather
OPC (Ordinary Portland Cement)7 days10 days minimumDepends on temperature and protection
PPC / PSC / mineral admixtures10 days14 days recommendedDepends on temperature and protection

Source: IS 456:2000, Clause 13.5.1. Cold-weather curing should be decided based on concrete temperature, protection and strength development rather than a fixed number of days.

Disclaimer: These curing periods are general guidelines. Actual curing time may vary depending on the cement, weather, concrete mix, and project requirements. Follow the applicable standards and project specifications.

How Long Should a Concrete Slab Be Cured?

A concrete slab should generally be water-cured for at least 7 days under moderate conditions when OPC is used. For blended cements, the curing period is generally 10 days or more. In hot and dry weather, curing may need to continue for 10–14 days. In cold weather, the required curing and protection depend on temperature and the rate at which the concrete gains strength.

What the curing period depends on

The curing period depends on cement type, temperature, humidity, exposure conditions, concrete mix and the strength required before formwork removal or loading.

When can curing be stopped?

Curing can generally be stopped once the required curing period has been completed and the concrete has reached the required strength for the work. In cold weather, additional protection may be needed because low temperatures slow down hydration and strength development.

Methods of Curing Concrete

Water curing (ponding, sprinkling and fogging)

Water curing keeps the concrete surface wet during the curing period. Ponding is suitable for flat surfaces such as slabs and roofs. Sprinkling and fogging can be used for walls, columns, and sloped surfaces.

For ponding, small bunds are made around the slab to hold water. Sprinkling and fogging apply water to the surface at regular intervals. The curing water should be clean and free from harmful substances. The concrete surface should not be allowed to dry repeatedly during the curing period.

Wet covering (hessian, gunny bags and burlap)

Wet hessian, gunny bags or burlap are placed over the concrete and kept wet. This method is useful for walls, columns and other surfaces where ponding is not practical. The covering needs regular re-wetting so that the concrete does not dry out.

Membrane curing (curing compounds)

Curing compounds are applied to the concrete surface to reduce moisture loss. They form a thin film over the surface and help retain the moisture needed for cement hydration. Membrane curing is useful for large pavements, sloped surfaces and sites where regular water curing is difficult.

The compound should be applied evenly at the coverage rate recommended by the manufacturer. Before applying plaster, paint, waterproofing or other finishes, check whether the curing compound is compatible with the planned finish.

Common Curing Compound Formulations

Compound formulationHow it worksTypical use
Resin-basedForms a film that reduces moisture loss from the concrete surfaceSlabs, pavements and general concrete work
Wax-basedForms a wax film that reduces moisture lossConcrete surfaces where a temporary curing film is suitable
Water-based acrylic/emulsionWater evaporates and leaves a continuous film on the surfaceLarge exposed concrete areas and applications where water-based products are preferred

Plastic sheeting and curing paper

Plastic sheets and curing paper cover the concrete surface and reduce moisture loss. The sheets should cover the surface properly and be secured at the edges. Poor placement can leave marks or cause uneven surface appearance.

Steam curing

Steam curing is mainly used for precast concrete. It uses controlled heat and moisture to accelerate early strength development. Because the process requires controlled temperature and moisture conditions, it is generally used in specialised precast production.

Self-curing and internal curing

Self-curing

Self-curing uses suitable materials or admixtures that help retain moisture within concrete and reduce moisture loss when conventional external curing is difficult.

Its suitability depends on the concrete mix, materials used and project requirements.

Internal curing

Internal curing supplies moisture from within the concrete mix so that hydration can continue as the concrete develops. It can use materials such as pre-soaked lightweight aggregate or super-absorbent polymers to store and release water within the concrete. The method should be selected as part of the concrete mix design.

Method comparison

MethodHow it worksWhere it is usefulKey consideration
Water curingMaintains moisture at the concrete surfaceSlabs, beams, columns, etc.Requires regular water supply
Membrane curingForms a film to reduce moisture lossLarge surfaces where water curing is difficultApplication must be uniform
Plastic sheetingCovers the surface to reduce evaporationFlat surfacesSheets must be properly sealed
Self-curingUses suitable materials or admixtures to help retain moistureAreas where conventional curing is difficultDepends on suitable material and dosage
Internal curingProvides stored moisture within the concrete mixSuitable specialised concrete mixesRequires appropriate materials and mix design

Curing Different Concrete Elements

Different concrete elements need different curing methods depending on their shape, size and exposure.

Concrete elementSuitable curing methodKey point
Slabs and roof slabsPonding, sprinklingFlat surfaces allow water to be retained or distributed
Columns and beamsWet hessian, sprinklingPonding is generally not practical
FootingsWater curing, wet coveringExposed surfaces need protection from drying
WallsWet covering, sprinkling or foggingSuitable for vertical surfaces
PavementsWater curing, wet covering or membrane curingChoice depends on water availability and site conditions

Curing of concrete cubes and test specimens

Concrete cubes used for strength testing should be cured under standard conditions as specified for the test. The curing water is generally maintained at 27 ± 2°C for standard testing.

Standard curing of concrete test specimens should follow the applicable requirements of IS 516.

Curing in Hot and Cold Weather

Weather has a direct effect on concrete curing. Hot weather can cause faster moisture loss, while cold weather slows down strength development.

Hot weather curing

In hot and dry weather, concrete can lose moisture quickly. Use shading, windbreaks, sprinkling, or fogging to keep the surface moist. Start curing once the surface is ready for the selected curing method.

Curing in Monsoon and Rainy Weather

Rain can provide moisture to concrete, but it should not be treated as a complete curing method because rainfall is not continuous or predictable. During the monsoon, the concrete surface should still be protected, and the selected curing method should be continued as required.

Heavy rain can also affect freshly finished concrete. Once rainfall stops, check the surface and continue the planned curing method. Waterlogging or uncontrolled runoff should not damage the concrete surface, and the curing method should suit the element and site conditions.

Cold weather curing

Cold weather slows down hydration and strength gain. Use insulating blankets or covers to protect the concrete and monitor its temperature. The concrete should also be protected from early freezing.

ACI 306R provides guidance on cold-weather concreting, including temperature control and protection during strength development.

References: IS 456:2000, IS 516, IS 7861 (Parts 1 and 2), IS 14494 and ACI 306R.

Note: Hot- and cold-weather concreting should also be considered with reference to the applicable requirements of IS 7861 (Parts 1 and 2).

Step-by-Step: How to Cure a Concrete Slab

  1. Start curing after the concrete has set and the surface will not get damaged.
  2. Make small bunds around the slab for ponding.
  3. Fill the slab with clean water and keep it wet.
  4. If ponding is not possible, use wet hessian or sprinkling.
  5. Check the surface regularly and add water when needed.
  6. In hot weather, increase watering and provide shade if possible.
  7. In cold weather, use suitable covers to protect the concrete.
  8. Continue curing for the required number of days.

Do not:

  • Allow the surface to dry during the curing period.
  • Remove curing measures before the required curing period.
  • Walk or place loads on the slab before it is ready.

How Concrete Mix Design Affects Curing?

Concrete mix design also affects the curing method and duration. Mixes with lower water content can dry faster and need proper curing. Blended materials such as fly ash can slow early strength gain and may require longer curing.

Chemical accelerators can speed up strength gain, but proper curing is still required. Mixes with high cement content can also generate more heat, so temperature control may be needed in some cases.

Conclusion

Proper curing is important for concrete to achieve the required strength and durability. The right method and curing period depend on the concrete, site conditions, and weather.

Plan the curing requirements with the concrete mix

Concrete mix design can affect moisture loss, strength development and temperature control during curing. Aparna RMC supplies concrete mixes designed for different project requirements, helping project teams select the appropriate concrete for the application and site conditions.

Frequently Asked Questions On Curing Of Concrete

Formwork removal and curing are separate activities. Formwork can sometimes be removed before curing is complete, but the exposed concrete surface should continue to be cured.

Light foot traffic is generally possible once the concrete has set. However, avoid activities that can damage the surface or disturb the curing method.

Start curing again as soon as possible. The curing period may need to be extended depending on how long the concrete was left without curing.

Curing water should be clean and suitable for use with concrete. Water containing high levels of salts, chlorides or organic matter should be avoided.

Rain can provide some moisture, but it should not be relied on as the only curing method because rainfall is not continuous or predictable.

Curing beyond the minimum period is generally not a problem and can support continued hydration and durability. However, the curing method, site conditions, construction sequence, and project requirements should be considered.

It depends on the type of curing compound and the finish planned over the concrete. Some compounds can affect the bond of plaster, paint, waterproofing or bonded toppings. Check the product manufacturer’s instructions before applying another finish.