M5 Concrete Ratio (1:5:10): Meaning, Cement Bags per m³, Quantities and Uses
November 18, 2026
The M5 concrete ratio is 1:5:10: one part cement, five parts sand and ten parts coarse aggregate (stone chips), measured by volume on site. M5 is a lean, non-structural grade with a 28-day compressive strength of 5 N/mm². It is used for levelling beds, blinding under footings and filling, never for slabs, beams or columns.
Watch a house foundation being built and you’ll notice that the first concrete poured into a footing pit isn’t the footing at all. It’s a thin grey bed that gives the steel fixers a clean, flat surface to work on and keeps the footing concrete away from the soil. That bed is often lean concrete, and M5 is the leanest grade in the Indian standard’s nominal-mix table.
This guide explains what the M5 concrete ratio of 1:5:10 actually means, how much cement, sand and aggregate to buy, and how to tell whether M5 is right for your job or whether you need something stronger.
Key Takeaways
- Ratio: 1:5:10 (cement : sand : coarse aggregate) is the common site ratio, measured by volume.
- What the code says: India’s concrete code, IS 456:2000, defines M5 by weight: up to 800 kg of sand and stone combined, and up to 60 litres of water, for every 50 kg bag of cement.
- Per cubic metre: about 2.8 bags of cement (≈139 kg), 0.48 m³ of sand and 0.96 m³ of 20 mm aggregate.
- Strength: 5 N/mm² at 28 days. That is one quarter of M20, the minimum grade the code allows for reinforced concrete.
- Use it for: levelling and blinding beds, mass filling, pipe bedding.
- Don’t use it for: reinforced (steel) work, or any surface people walk or drive on.
What Is M5 Grade Concrete?
M5 grade concrete is a low-strength, lean mix of cement, sand, coarse aggregate and water. In the name, “M” stands for mix. “5” is the compressive strength in newtons per square millimetre (N/mm², the same as MPa) that a 150 mm test cube should reach 28 days after casting.
M5 sits at the very bottom of the grade ladder. The main grades table in the code starts at M10. M5 and M7.5 appear only in the standard’s table of nominal (fixed-recipe) mixes, which tells you what M5 is for: simple, non-structural work.
What Does 5 N/mm² Actually Mean?
Five newtons on every square millimetre works out to roughly 51 kg on every square centimetre. Picture a small adult balanced on a patch the size of a fingertip. That’s ample for a bed that only has to stay flat and hold its shape while a footing is built on top of it.
It’s nowhere near enough for a structure. M20, the minimum grade allowed for reinforced concrete, is four times stronger.
The 5 is also a floor, not an average. Engineers call it the characteristic strength: the value below which no more than 5% of test results are expected to fall.
Why M5 Is Called Lean Concrete?
“Lean” means low in cement. In M5, one part of cement has to coat fifteen parts of sand and stone, so the cement paste is spread very thin. Think of cement as the glue in the mix. There’s enough glue to lock the stones in place, but not enough to make them carry serious load together.
That’s why the code treats grades like M5 as a special case. It allows them for lean concrete, foundations for masonry walls and temporary works, not as general-purpose concrete.
M5 Concrete Ratio: 1:5:10 Explained
The M5 ratio is a recipe in parts. Whatever you measure with, a box or a bucket, fill it once with cement, five times with sand and ten times with coarse aggregate. That gives 16 parts of dry material, and only one of them is cement.
| Part of the ratio | Material | Share of the dry mix | What it does |
|---|---|---|---|
| 1 | Cement | 1 of 16 (≈6%) | The binder. It reacts with water and glues everything together. |
| 5 | Sand (fine aggregate) | 5 of 16 (≈31%) | Fills the gaps between the stones and makes the mix workable. |
| 10 | Coarse aggregate (usually 20 mm stone chips) | 10 of 16 (≈63%) | The bulk of the concrete. It gives volume and a stable skeleton. |
| — | Water | Not part of the ratio | Starts the cement reaction. The amount is controlled separately (see below). |
Is the M5 Ratio by Volume or by Weight?
On site, 1:5:10 is measured by volume. The Indian standard works by weight. IS 456:2000 (Table 9) does not print “1:5:10” at all. It defines M5 like this:
| IS 456 Table 9 (by weight, per 50 kg bag of cement) | M5 value |
|---|---|
| Total dry aggregate (sand + stone together), maximum | 800 kg |
| Split of sand to stone | Generally 1:2 by weight (allowed range 1:1.5 to 1:2.5) |
| Water, maximum | 60 litres |
| Same thing written as a weight ratio (20 mm stone) | ≈ 1 : 5.3 : 10.7 |
The site shorthand of 1:5:10 lands close to the code because loose cement, dry sand and stone chips weigh roughly similar amounts per litre. It’s a practical approximation, not a code figure. The code itself expects cement and aggregate to be batched by weight.
Converted to weights per cubic metre, the code values come to roughly 130 kg of cement, 700 kg of sand and 1,400 kg of 20 mm stone, plus water. That is the “M5 ratio in kg” many people search for.
The sand-to-stone split also depends on stone size. For average sand, the standard suggests 1:1.5 with 10 mm stone, 1:2 with 20 mm and 1:2.5 with 40 mm. So “1:5:10” quietly assumes 20 mm aggregate.
How Much Cement, Sand and Aggregate for 1 m³ of M5 Concrete?
To make 1 m³ of M5 concrete you need about 2.8 bags (≈139 kg) of cement, 0.48 m³ (≈17 cft) of sand and 0.96 m³ (≈34 cft) of 20 mm aggregate, plus up to 60 litres of water per bag of cement.
| Material (per 1 m³ of M5) | Volume | In site units |
|---|---|---|
| Cement | 0.096 m³ | ≈ 2.77 bags of 50 kg (≈139 kg) |
| Sand | 0.48 m³ | ≈ 17 cft |
| Coarse aggregate (20 mm) | 0.96 m³ | ≈ 34 cft |
| Water | — | Up to ≈166 litres (60 L per bag × 2.77 bags), usually less |
Based on the common 1.54 dry-volume method and cement at 1,440 kg/m³. Add your wastage allowance (5–10% is common) before ordering.
The Calculation in Three Steps
- Allow for shrinkage. Dry materials take up more space than the finished concrete, because sand settles into the gaps between stones once water is added. Indian site practice multiplies the wet volume by 1.54: 1 m³ × 1.54 = 1.54 m³ of dry material.
- Split it into 16 parts. 1 + 5 + 10 = 16, so one part = 1.54 ÷ 16 = 0.096 m³.
- Multiply. Cement = 1 part = 0.096 m³ × 1,440 kg/m³ = 138.6 kg = 2.77 bags. Sand = 5 parts = 0.48 m³. Aggregate = 10 parts = 0.96 m³.
How Many Cement Bags for M5 Concrete?
Plan on about 2.8 bags of 50 kg cement per cubic metre. You’ll see figures from about 2.5 to 2.8 online, and the gap comes from method rather than mistakes:
- The volume method above gives 2.77 bags.
- Working from the code’s weight-based values (50 kg cement + 800 kg aggregate + water per batch, in concrete that weighs about 2.4 tonnes per m³) gives roughly 2.6–2.7 bags.
Either way, a cubic metre of M5 uses less than three bags. For comparison, M20 uses about eight.
Quantities for Common Volumes
| Concrete needed | Cement (50 kg bags) | Sand | Coarse aggregate |
|---|---|---|---|
| 0.5 m³ | 1.4 | 0.24 m³ (≈8 cft) | 0.48 m³ (≈17 cft) |
| 1 m³ | 2.8 | 0.48 m³ (≈17 cft) | 0.96 m³ (≈34 cft) |
| 2 m³ | 5.5 | 0.96 m³ (≈34 cft) | 1.93 m³ (≈68 cft) |
| 5 m³ | 13.9 | 2.41 m³ (≈85 cft) | 4.81 m³ (≈170 cft) |
| 10 m³ | 27.7 | 4.81 m³ (≈170 cft) | 9.63 m³ (≈340 cft) |
Wastage not included. Use the RMC volume calculator to work out the volume of footings and slabs first.
Batching One Bag at a Time
Most site batches are built around one bag of cement. A 50 kg bag holds about 35 litres (1.23 cft) of cement, so a measuring box of the same size makes the ratio easy to follow:
| Per batch | Quantity | Measured as |
|---|---|---|
| Cement | 1 bag (50 kg) | ≈ 35 L / 1.23 cft |
| Sand | 5 boxes | ≈ 174 L / 6.1 cft |
| Coarse aggregate | 10 boxes | ≈ 347 L / 12.3 cft |
| Water | Up to 60 L | Add gradually; use the least that makes the mix workable |
| Yield | ≈ 0.36 m³ of M5 | About 13 cft of finished concrete per bag |
How Much Water Does M5 Need?
The code caps water for M5 at 60 litres per 50 kg bag of cement, and adds that durability may call for less. In practice, use the least water that lets the mix be spread and compacted properly. Extra water makes it easier to pour, but it also makes the concrete weaker.
Myth check: the “0.5–0.6” water–cement ratio
You’ll often see “0.5 to 0.6” quoted as the water–cement ratio for M5. That range suits richer mixes, not M5.
M5 has so little cement (about 139 kg per m³) that a ratio of 0.5 would mean only about 70 litres of water in a whole cubic metre. That’s far too dry to spread and compact.
The code’s limit of 60 litres per bag works out to a ratio of up to 1.2. The number looks high only because there’s very little cement to compare the water against. For how the ratio works in general, see water-cement ratio in concrete.
Worked Example: Levelling Beds for a House Foundation
Say a house has 12 footing pits, each 1.5 m × 1.5 m, and the drawing asks for a 75 mm M5 levelling bed in each. (These are example values. Always use the sizes and thickness on your own drawing.)
- Volume = 12 × 1.5 × 1.5 × 0.075 = 2.03 m³
- Add 5% wastage: 2.03 × 1.05 = 2.13 m³
- Cement = 2.13 × 2.77 = 5.9, so 6 bags
- Sand = 2.13 × 0.48 = 1.02 m³ (≈36 cft)
- Aggregate = 2.13 × 0.96 = 2.04 m³ (≈72 cft)
How Strong Is M5 Concrete?
M5 concrete has a characteristic compressive strength of 5 N/mm² at 28 days. Like any concrete it keeps gaining strength after it is cast. 28 days is simply the age at which the grade is judged.
For context, 5 N/mm² is enough to hold a flat working surface or fill a void without crumbling. It is not enough to carry a building’s loads or protect steel from rust, which is why structural grades start at M20.
Curing M5 Concrete
Lean doesn’t mean you can leave it to dry out. The code asks for exposed concrete to be kept continuously wet for at least 7 days with ordinary Portland cement (OPC), and at least 10 days with blended cements such as PPC or when mineral admixtures are used. It also asks for at least 10 days in hot, dry weather. Ponding, wet hessian or regular sprinkling all work. More on methods: concrete curing.
Where Is M5 Concrete Used?
M5’s job is to be a clean, level, stable base, or to fill space. It isn’t meant to hold the building up. Typical uses:
- Levelling course / blinding under footings and rafts. A thin bed, commonly 50–100 mm thick: 50–75 mm for light residential footings on firm, level soil, and about 100 mm for commercial buildings, deeper foundations or uneven, loose soil. Follow your drawing. The bed stops footing concrete from mixing with soil, keeps reinforcement off the mud and gives a true surface for marking out.
- Foundations for masonry walls, where the designer permits a lean grade.
- Mass filling: making up levels in pits, trenches and voids.
- Bedding for pipes and drains, to give them an even, firm support.
- Temporary works that will be removed or covered.
Where M5 Should Not Be Used
- Slabs, beams, columns or RCC footings. Permanent reinforced concrete needs at least M20 under the code. If you searched for an “M5 concrete ratio for slab”, the honest answer is that there isn’t one. Start with the M20 concrete ratio.
- Finished surfaces: floors, paths, driveways or anything walked or driven on and left exposed. These need a stronger grade (see the FAQs below).
- Any element your drawing specifies a grade for. Never swap in a leaner mix to save cement.
M5 vs M7.5 vs M10 vs M15: Which Lean Grade Do You Need?
The four nominal lean grades differ mainly in how much cement each cubic metre gets. More cement means more glue, more strength and better durability.
| Grade | Site ratio (by volume) | IS 456 Table 9: max aggregate per 50 kg cement | Max water per 50 kg cement | Cement per m³ (approx.) | Typical role |
|---|---|---|---|---|---|
| M5 | 1:5:10 | 800 kg | 60 L | 2.8 bags (≈139 kg) | Levelling beds, blinding, mass fill |
| M7.5 | 1:4:8 | 625 kg | 45 L | 3.4 bags (≈171 kg) | Levelling courses, PCC bedding under brick/stone foundations, pipe bedding, sub-bases under light pathways |
| M10 | 1:3:6 | 480 kg | 34 L | 4.4 bags (≈222 kg) | Standard PCC bed under RCC footings, ground-floor slab sub-bases, kerb backing |
| M15 | 1:2:4 | 330 kg | 32 L | 6.3 bags (≈317 kg) | Plain concrete exposed to soil, moisture or rain: open drains, compound-wall foundations, plinth protection |
Cement per m³ uses the same 1.54 dry-volume method as above. Water figures are code maximums.
Here’s how to read it. For plain concrete that has to be durable on its own, the code sets minimums: at least 220 kg of cement per m³ in mild conditions, and at least M15 (240 kg) wherever concrete is in contact with soil or exposed to rain. M5, at about 139 kg, falls well below both. It’s allowed only because the code makes a specific exception for lean concrete.
So treat M5 as a working layer, not as concrete that has to last on its own. If your plain-concrete layer will be exposed, or your engineer wants a sturdier PCC bed, step up to M10 or M15. For M10 quantities, see the M10 concrete ratio. For every grade from M5 to M80 and the full exposure table, see grades of concrete.
Getting the M5 Mix Right on Site
- Measure with a box, not shovels. Shovel loads vary from worker to worker. A box sized to one cement bag (about 35 litres) keeps every batch at 1:5:10.
- Watch for damp sand. Wet sand swells (this is called bulking), so a box of damp sand holds less sand than a box of dry sand. When batching by volume, add about 15–25% extra sand, depending on how fine and how damp it is; very fine sand and M-sand with a lot of fines bulk the most. To check on site, fill a jar with damp sand to a marked level, flood it with water, stir out the air and see how far the level drops.
- Mix dry first. Blend cement and sand until the colour is even, add the aggregate, then add water gradually.
- Don’t flood the mix to make it flow. Stay within 60 litres per bag, and use less if the mix allows.
- Prepare the ground. Place M5 on firm, cleared, compacted soil, then level and compact the concrete.
- Cure it for the full 7 or 10 days.
Ordering Lean Concrete from Aparna RMC
Hand-mixing a few bags is fine for a single pit. For a full set of footing beds, a raft blinding layer or mass filling, plant-batched ready mix concrete takes the guesswork out of the ratio. Cement and aggregate are weighed rather than counted in shovels, water is metered, and the concrete arrives ready to place.
Aparna RMC supplies ready mix concrete from plants serving Hyderabad, Bengaluru, Chennai, the Mumbai region, Visakhapatnam and Mangaluru, with lean, non-structural grades alongside structural and high-grade concrete. Aparna RMC does not batch M5. When a drawing calls for M5, it supplies M7.5 (1:4:8) as the standard replacement, or M10 where the PCC bed sits directly under RCC footings in damp soil. Very lean mixes segregate easily in transit mixers and are hard to pump or chute, while M7.5 still does the levelling job M5 was specified for. Estimate your volume with the RMC calculator, then request a quote with the grade, quantity and placement method.
Frequently Asked Questions On M5 Concrete
Is M5 concrete the same as PCC or lean concrete?
M5 is one grade of PCC (plain cement concrete, meaning concrete without steel reinforcement). “Lean concrete” describes any low-cement mix. M5 is the leanest grade in IS 456’s nominal-mix table, followed by M7.5 and M10. When a drawing just says “PCC bed”, check which grade it names.
Can M5 concrete be used for a pathway or driveway?
No. A path or driveway is exposed to rain and sits on soil. IS 456 classes that as moderate exposure and sets M15 as the minimum grade for plain concrete there. Driveways that carry vehicles usually need more, chosen by an engineer. A lean grade such as M7.5 can still be used as the sub-base underneath.
What is the minimum cement content for M5 concrete?
IS 456 does not set a separate minimum for M5. It controls M5 by capping aggregate at 800 kg per 50 kg bag of cement, which works out to about 130–140 kg of cement per m³. That is below the 220 kg/m³ the code asks of durable plain concrete, which is one reason M5 is limited to lean work.
Can M5 concrete be mixed by hand?
IS 456 expects concrete to be mixed in a mechanical mixer, for at least about two minutes, until the colour and consistency are even. Small lean pours are still often hand-mixed on house sites. If you do, use a clean, hard platform. Standard site practice (not part of IS 456) is to add 10% extra cement to make up for less thorough mixing. For 1 m³ of M5, that raises cement from about 2.77 to about 3.05 bags (≈152 kg).
How much does 1 m³ of M5 concrete weigh?
Around 2.4 tonnes. IS 456 lets designers take plain concrete made with normal sand and stone as 24 kN/m³ (about 2,450 kg per m³) unless more accurate figures are needed. The actual weight depends on the aggregate used.
Categories
Recent Posts
Connect with us